/* DVD IR Synchronizer for Philips DVP3142/12
 * Code written by Joe Foley <foley@ru.is>
 * on 2013-09-08
 *
 *
 * Requires libraries:
 *  Arduino-IRremote https://github.com/shirriff/Arduino-IRremote
 *   Instructions http://www.righto.com/2009/08/multi-protocol-infrared-remote-library.html
 *
 * IR Remote codes  from IRrecvDemo
 *
 *  The IRremote library uses Pin 3 for the Anode (longer pin)
 *  We have made a ground pin on Pin 4 for the Cathode (shorter pin)
 */


#include <IRremote.h>

int pinGND=4;  // Longer leg on the IR LED
int pinLED=13; // The heartbeat LED on the board

int heartbeat=0;
int secs;
int playtime= 1*60+1;      // Play time in seconds, you usually leave off a second or two

IRsend irsend;

void setup() {
  pinMode(pinGND,OUTPUT);
  pinMode(pinLED,OUTPUT);
  Serial.begin(115200);

  Serial.println("Scott DVX605 HD(Rev2) Synchronizer $Rev$");
  Serial.println("For \"$INSTALLATION NAME$\" by $ARTIST$ ($YEAR$)");
  Serial.println("Code by Joe Foley <foley@ru.is>");
  Serial.println("$URL$");
  Serial.println("$Id$");
  Serial.print("Playtime: ");
  secs=playtime;
    Serial.print("sec:");
    Serial.print(secs);
    Serial.print(" / mm:ss ");
    Serial.print(secs/60);
    Serial.print(":");
    Serial.print(secs % 60);
    Serial.println("");

  secs=playtime;

}

/********************************************************************/
void loop() {
  Serial.println("Sync");
  //send_pause();
  //waitsec(2);

  send_previous();
  send_previous();
  send_previous();
  //waitsec(2);      
  // Don't send play because previous automatically starts it
  // If we hit play it will merely pause it.
  //send_play();  

  for(int t = 0; t < playtime; t++) {
    // This will not give us perfect 1 second timing
    //   but it is good enough for most video applications
    // The most critical is having everything start at the
    //   same time.
    Serial.print("sec:");
    Serial.print(playtime);
    Serial.print(" / mm:ss ");
    Serial.print(t/60);
    Serial.print(":");
    Serial.print(t % 60);
    Serial.println("");
    if (heartbeat == 1) {
      digitalWrite(pinLED, HIGH);
      heartbeat = 0;
    }
    else {
      digitalWrite(pinLED, LOW);
      heartbeat = 1;
    }
    delay(1000);
  }

}

/**************************************************************/
void waitsec(int sec) {
  Serial.print("Wait ");
  Serial.print(sec);
  Serial.println(" seconds");
  delay(sec*1000);
}


/********************************************************************/
void send_stop() { 
  // First comes the pre-data bits, then the command code
    Serial.println(" stop");
    irsend.sendNEC(0xFFC837,32); 
}

/********************************************************************/
void send_play() { 
  // First comes the pre-data bits, then the command code
    Serial.println(" play");
    irsend.sendNEC(0xFFF00F,32); 
}

/********************************************************************/
void send_pause() { 
  // First comes the pre-data bits, then the command code
  Serial.println("  pause");
  irsend.sendNEC(0xFFD02F,32); 
}	

/********************************************************************/
void send_previous() {  
  // First comes the pre-data bits, then the command code
  Serial.println(" previous");
  irsend.sendNEC(0xFF50AF, 32); 
}